Check different types of pumps

 In this article, we are going to introduce pumps. After defining the pump, we will examine its types. Stay with us.

Pumps are devices that convert electrical energy into hydraulic energy using fluid motion .But what does the Head of a Pump

mean? The pump head is a measure of pump power. The higher the pump head, the greater the pressure that the pump can create. Will be. More Here at Linquip

What is Pump Curve?

The system curve is a graphical representation of the energy equation. The system head described in the system curve above is a function of static height or head. Primary and secondary losses in the system can be expressed as follows: Click Here

Each type of pump has a specific diagram, and the date marked on them are also different models.

The first impression to consider is that the pressure, which represents the head, appears typically on the central vertical Y-axis. On the horizontal X-axis, we usually have the flow velocity, describing how much water the pump can transfer. See More

Hydraulic Pumps

Hydraulic pumps are used in hydraulic actuator systems and can be hydrostatic or hydrodynamic. A hydraulic pump is a mechanical source of force that converts mechanical force into hydraulic energy. What are the Different Types of Hydraulic Pumps?

The different types of hydraulic pumps are as follows:

  • Reciprocating pumps
  • Rotary pumps
  • Gear pumps
  • External gear pumps 

Click Here

Gear Pumps: Probably the simplest and most commonly used types of hydraulic pumps today and they are easily maintained and economic. Read More in Linquip


Comments

Post a Comment

Popular posts from this blog

Everythings about Gas Turbine

Image
In this article, we are going to introduce a gas turbine. We will also examine the Gas Turbine Cycles and its different types. What is Gas Turbine: A gas turbine, also called a combustion turbine, is a type of continuous and internal combustion engine. The main elements common to all gas turbine engines are: an upstream rotating gas compressor a combustor a downstream turbine on the same shaft as the compressor. The first gas turbine type was turbojet engines. Although they look entirely different from reciprocal engines, they operate on the same principle: intake, compression, power and exhaust. In this type of engine, air is moved at a high speed to the fuel inlet and ignitor of the combustion chamber. The turbine induces accelerated exhaust gases by expanding air. Click here to read more about different types of gas turbine . Which cycle is used for gas turbine ? The basic operation of this turbine type has roots in the gas turbine cycle which is also known as the Brayton cycle. ...
Read more

How To Increase Cooling Tower Efficiency?

Image
  cooling towers. A device for dissipating heat from processes such as water evaporation. In this article, we will introduce solutions for Increasing Cooling Tower Efficiency . Stay with us. The U.S. Department of Energy (DOE) is proposing to provide funding to the State of Arizona to replace parts of the heating, ventilation, and air condition system that have reached their expected useful life with more energy-efficient equipment at the Arizona State Veterans’ Home in Phoenix, AZ. Specifically, the cooling towers, condenser pumps, air dirt separator, interconnecting piping with valves and fittings, and the controls would be replaced. a cooling tower is a heat rejection device that rejects waste heat to the atmosphere through the cooling of a water stream to a lower temperature. Cooling towers may either use the evaporation of water to remove process heat and cool the working fluid to near the wet-bulb air temperature or, in the case of closed circuit dry cooling towers, rely sol...
Read more

Introduction of electric motors and types

Image
  You've probably heard of electric motors by now. A critical piece in all electrical appliances. In this article, we will introduce electric motors in detail and examine its types, so stay tuned. An electric motor is a component that converts electrical energy into kinetic energy. Most electric motors are  electromagnetic -based. Most electric motors are rotary, but there are also linear motors. In a rotating motor, the moving part (usually inside the engine) is called the impeller or rotor, and the fixed position is called the station or stator. The motor consists of electric magnets wound on a frame. Although this frame is often referred to as armature, the term is often misused. Types of Electric Motor Electric motors may be classified by considerations such as power source type, internal construction, application and type of motion output. In addition to AC versus DC types, motors may be brushed or brushless, may be of various phase (see single-phase, two-phase, or three-...
Read more